DynaMix Power
Home › Spare Parts › metso › c-jaw
Fixed and movable jaw plates, toggle plates and side liners for Metso C63, C80, C96, C100, C106, C110, C125, C140, C145, C160 and C200.
Fixed and movable jaw plates, toggle plates and side liners for C63 through C200. Eleven models, one drawing per plate profile, and the profile is where the money is decided.
Jaw plates are the simplest wear part in the plant and the one most often bought on price alone. That is a mistake we see on repeat orders: the cheaper plate with the wrong tooth pitch wears out in three weeks and the customer never compares the cost per tonne, only the invoice.
A coarse feed needs tall, widely spaced teeth so the plate can grip and the material is crushed rather than ground. A fine feed wants a lower profile, otherwise the teeth never fill and the plate wears on the tips. Fitting a fine-tooth plate behind a primary blast feed gives poor grip, higher power draw and a short life. We ask for the feed curve and the closed side setting before recommending a profile, and we will say plainly when the profile the customer asked for is the wrong one for their feed.
A toggle is designed to bend or break before the frame does. When a plant reports toggles failing twice in a season, the toggle is doing its job and something upstream is feeding tramp metal or overfilling the chamber. Selling a stronger toggle in that situation moves the failure into the frame, which is the expensive end. We ask what broke first.
The last 150 mm above the discharge opening does most of the crushing, because that is where the stroke is largest and the material is smallest. A plate that looks half worn across its face is often 80 percent used at the bottom. Measuring only the mid-face gives a false sense of remaining life, which is how a plate gets run until it cracks. Measure near the discharge end.
| Model | Parts | Chamber options | Material |
|---|---|---|---|
| C100 | Movable Jaw Plate, Fixed Jaw Plate, Toggle Plate | — | Mn18Cr2, Mn13Cr2 |
| C105 | Fixed Jaw Plate, Movable Jaw Plate, Toggle Plate | — | Mn18Cr2, Mn13Cr2 |
| C106 | Movable Jaw Plate, Fixed Jaw Plate | — | Mn18Cr2 |
| C110 | Fixed Jaw Plate, Movable Jaw Plate, Toggle Plate | — | Mn18Cr2, Mn13Cr2 |
| C125 | Movable Jaw Plate, Fixed Jaw Plate, Toggle Plate | — | Mn18Cr2, Mn13Cr2 |
| C140 | Fixed Jaw Plate, Movable Jaw Plate, Toggle Plate | — | Mn18Cr2, Mn13Cr2 |
| C145 | Movable Jaw Plate, Fixed Jaw Plate, Toggle Plate | — | Mn18Cr2, Mn13Cr2 |
| C160 | Movable Jaw Plate, Fixed Jaw Plate, Toggle Plate | — | Mn18Cr2, Mn13Cr2 |
| C200 | Movable Jaw Plate, Fixed Jaw Plate, Toggle Plate | — | Mn18Cr2, Mn13Cr2 |
| C63 | Fixed Jaw Plate, Movable Jaw Plate, Toggle Plate, Tension Rod | — | Mn18Cr2, Mn13Cr2, carbon steel |
| C80 | Fixed Jaw Plate, Movable Jaw Plate, Toggle Plate | — | Mn18Cr2, Mn13Cr2 |
| C96 | Movable Jaw Plate, Fixed Jaw Plate | — | Mn18Cr2 |
Lead time: 15 to 30 days from drawing or sample
C63, C80, C96, C100, C105, C106, C110, C125, C140, C145, C160 and C200. Fixed and movable plates are listed for each in the table.
Yes, to drawing. Profiles vary by application more than by model, so the drawing governs. Send the existing plate or its drawing and we quote from that.
Yes, though they are not all castings. Toggles and tension rods are often cut from plate or bar and machined, which we do as an outsourced item against the drawing.
Brand names and model designations on this page describe which machines the parts fit. Shanghai Dynamix Power is an independent manufacturer of aftermarket replacement wear parts and is not affiliated with, authorised by, sponsored by or endorsed by any original equipment manufacturer. Original part numbers, where shown, are cross-references for identification only.
METSO™, SANDVIK®, SYMONS®, TEREX®, KLEEMANN®, TELSMITH® and HAZEMAG® are trademarks or registered trademarks of their respective owners.
Tel / WhatsApp: +86 18616330128 | E-mail: ensaichen@dynamixpower.com