DynaMix Power
Home › Spare Parts › shanbao
Jaw plates, mantles and bowl liners for Shanbao PE jaw crushers and PYB, PYD cone crushers, made to drawing or sample.
Shanbao covers two families we cast for: the PE jaw range and the PYB and PYD cone range. Nine models between them, listed with their parts in the table below.
The practical difficulty with this brand is not the casting. It is that two machines carrying the same plate often leave the factory with different castings, because the design has been revised quietly over the years and the plate was not always updated with it.
PE is the jaw series. In the cone range, PYB is the standard cavity and PYD is the short head, and the two use different liners for the same nominal size. An enquiry that says "900 cone" without the prefix can be either. We ask for the plate, and where the plate is missing we ask for a photograph of the liner in place, because the bowl shape identifies it faster than any measurement.
Frames built years apart under the same plate number can take plates with different fixing geometry. This is not a defect and it is not something a part number reveals. Before we cut, we ask for the existing plate or its drawing. Where neither exists, we say the quotation is conditional and explain what would make it firm.
Mn18Cr2 is our default for both jaw plates and cone liners on this range. On a PE jaw taking a hard, blocky feed we will quote Mn22Cr2 for the movable plate, because the top of the plate takes the impact and a tougher grade pays for itself there even though the wear resistance is lower.
| Model | Parts | Chamber options | Material |
|---|---|---|---|
| PYB-2200 | Mantle, Concave, Bowl Liner | — | Mn18Cr2 |
| PYB-900 | Mantle, Bowl Liner, Concave | — | Mn18Cr2 |
| PYD-1750 | Mantle, Concave, Bowl Liner | — | Mn18Cr2 |
| PE-1200x1500 | Fixed Jaw Plate, Movable Jaw Plate | — | Mn18Cr2 |
| PE-400x600 | Fixed Jaw Plate, Movable Jaw Plate, Toggle Plate | — | Mn18Cr2, Mn13Cr2 |
| PE-500x750 | Fixed Jaw Plate, Movable Jaw Plate, Toggle Plate | — | Mn18Cr2, Mn13Cr2 |
| PE-600x900 | Movable Jaw Plate, Fixed Jaw Plate, Toggle Plate | — | Mn18Cr2, Mn13Cr2 |
| PE-750x1060 | Fixed Jaw Plate, Movable Jaw Plate, Toggle Plate | — | Mn18Cr2, Mn13Cr2 |
| PE-900x1200 | Fixed Jaw Plate, Movable Jaw Plate, Toggle Plate | — | Mn18Cr2, Mn13Cr2 |
Lead time: 15 to 30 days from drawing or sample
PE-400x600, PE-500x750, PE-600x900, PE-750x1060, PE-900x1200, PE-1200x1500, PYB-900, PYB-2200 and PYD-1750.
Usually from a photograph of the bowl in place or the old liner. The cavity shape differs. If neither is available we ask you to measure the bowl and confirm before we pour.
For some. Every row in the table states whether it runs from a pattern we hold or is made to drawing, so the delivery date is not built on an assumption.
Brand names and model designations on this page describe which machines the parts fit. Shanghai Dynamix Power is an independent manufacturer of aftermarket replacement wear parts and is not affiliated with, authorised by, sponsored by or endorsed by any original equipment manufacturer. Original part numbers, where shown, are cross-references for identification only.
METSO™, SANDVIK®, SYMONS®, TEREX®, KLEEMANN®, TELSMITH® and HAZEMAG® are trademarks or registered trademarks of their respective owners.
Tel / WhatsApp: +86 18616330128 | E-mail: ensaichen@dynamixpower.com